#FESTOOL LR32 PLUS#
#FESTOOL LR32 SERIES#

I use the KISS II system which has the first hole staring at 35mm so I had custom bars machined to facilitate that. But I have seen past posts here and been watching a lot of YT videos. To me, shelf pins need holes and drawer slides need holes, both completely different (to me at least). There really isn't a single answer.įor doors, the cup hinges on the doors are centered between 32mm holes so if you start with 16 up and out for the cabinet sides, you need to drill the cup hinges with 32 up and out on the doors and vice versa. Shelf pins, drawer slides, LR-32 on: March 02, 2020, 09:21 AM My current project gave me my first time to do drawer slides. I have other slides where the hole is 16mm from the bottom and some where it is 25mm from the bottom. 32 up and out has your first hole at 32mm or 64mm Since 48 isn't enough, 32 isn't either so your first hole would be best placed at 64mm. Subtract 19mm from 48 and you only have 29mm but need 37. Since you have a 19mm bottom on the cabinet, 16 is out which leaves 48 as your first hole. If you use 16 up and out, your first hole will be a 16 or 48 mm. This system allows you to drill 5mm holes at 32mm centers in a repeatable and accurate.

#FESTOOL LR32 SERIES#

Blum 563 series slides have the hole 37mm up from the cabinet side. Festool LR 32 System, In this two part video we look at the shelf pin and hinge drilling system from Festool. You then need to figure out where you need the holes based on the thickness of your tops and bottoms for the cabinets, and the drawer slides you are using. Festool Hole drilling set LR 32 Set Strengths and benefits Hole line guide plate for. The most basic answer is that 16 up and out will set the center of the first hole 16mm from the top or bottom and 32 up and out will set the hole 32mm from the top or bottom. Brand Festool Order number: F-583290 Weight 2.403 kg.

#FESTOOL LR32 PLUS#

When you use 9.5 up and out, the sides will be a multiple of 32mm, PLUS 19mm to accommodate the top and bottom in the Ikea paradigm. Whether you use the 16 up and out or 32 up and out, the sides will be a multiple of 32mm. So why 9.5? Tops and bottoms are 19mm thick. In this case, think of how Ikea joins tops and bottoms to sides as an example. You'll note, too that there's a 9.5 setting for those cases when you use Confirmat screws to join sides of a cabinet to the top or bottom of the cabinet. When you put 32 up and out, you can set the system to put the first hole 32mm down from the top (or 32mm up from the bottom).

This setting can also be used to set the top hole 16mm down from the top of the casework (or up 16mm from the bottom of the casework). dowel drill with 5 mm diameter and fastening clamps.Ĭompatible with and can be connected to all Systainer generations, mobile dust extractors and many other system accessories.When you use the 16 up and out, the stop block can be used as a temporary spacer so that two LR 32 rails can be joined end-to-end while maintaining correct spacing to continue the 32mm system spanning both rails without error. LR 32: With the LR 32 Hole Drilling System from Festool, you can precisely and. Highly efficient production of series of holes with 32 mm spacing.Įverything together, everything well organised, everything is close to hand in the SYSTAINER – the complete set incl. The team walks you through the features of the Festool LR 32 Hole Drilling System. The hole series drilling system is a complete set for fast and simple production of series of holes for shelf supports, rear wall supports and fittings with the OF 1010 or OF 1400 router. Using LR32 System, OF1010 Router, MFT Table, CT26 plus more. Hole series are always drilled with a spacing of 32 mm and a hole diameter of 5 mm or 3 mm. Septem130 likes, 0 comments - Festool Canada (festoolcanada) on Instagram: ''Making cabinets for the shop.

2 parallel side fences with adjustable stop.This system is used primarily in cabinetmaking. The Festool LR32 system is a line boring system that allows for boring a row of holes in a piece of wood that are exactly 32mm apart (on center). Includes Split anchor 50x Bolt with Euro thread for drilling series of.

The Festool LR32 adaptor is designed to fit onto the base of the OF900/OF1000/OF1010/OF1400 routers using thumb screws, so it really depends on how big the base of your Bosch router is. Product Description This 3D printed part is for use with the Festool LR32 System and the Blum Process32 cabinet construction method.

dowel drill HM Ø 5 mm (with centring bit and pre-cutter) 2 (Edited) Hi Derrills I'm assuming that your router has a plunge base, otherwise this isn't going to work.

Festool lr32